Dismiss Notice

Welcome To CK5!

Registering is free and easy! Hope to see you on the forums soon.

Score a FREE t-shirt and membership sticker when you sign up for a Premium Membership and choose the recurring plan.

got my 1ton rear output [pics]

Discussion in '1973-1991 K5 Blazer | Truck | Suburban' started by mike reeh, Apr 24, 2002.

  1. mike reeh

    mike reeh 1/2 ton status

    Joined:
    Jul 23, 2001
    Posts:
    752
    Likes Received:
    0
    Location:
    San Diego, CA
    just thought Id share... 1 ton np205 output yoke, <a target="_blank" href=http://lagparty.org/~mike/pix/yoke.jpg>pictured</a> next to the original 1/2ton yoke

    thanks to TX_Mudder for helping me out (a long time ago)

    mike
     
  2. Esteban86K5

    Esteban86K5 1/2 ton status

    Joined:
    Feb 17, 2000
    Posts:
    3,712
    Likes Received:
    0
    Location:
    Bakersfield, CA
    Damn, that thing is huge!!!! I'm in the same boat as you. I'm about to get a 1 ton Cv from High Angle so I'll share the comparison when I get it.

    How's the build up going? Are we gonna see you again soon?
     
  3. m j

    m j 1/2 ton status

    Joined:
    Dec 28, 2001
    Posts:
    4,606
    Likes Received:
    0
    so what is it?
    1350? 1410?
     
  4. mike reeh

    mike reeh 1/2 ton status

    Joined:
    Jul 23, 2001
    Posts:
    752
    Likes Received:
    0
    Location:
    San Diego, CA
    MAN I want the CV but its too cost prohibitive right now.. later on when the trucks driving and I can save some $$, I might go that route..

    the truck is coming along awesomely, im really pleased with it.. of course, im spending wayyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyy more time and money than originally planned but I love every second of it. Its a rolling chassis and the motor/trans/case are all ready to be dropped in, hopefully will do that this weekend and post some pix.

    The thing should be running &amp; ready for wheelin in a few months.. what trips are planned? any in the next few? been laggin with keeping up with the big dawgs......

    mike
     
  5. Esteban86K5

    Esteban86K5 1/2 ton status

    Joined:
    Feb 17, 2000
    Posts:
    3,712
    Likes Received:
    0
    Location:
    Bakersfield, CA
    Sounds good. Are you gonna want to wheel it after you are done. IT'LL BE SO PURTY!!/forums/images/icons/wink.gif

    There are a few runs set up. The weekend of May 18 a run to Los Coyotes is set-up. The weekend of May 25 a run up tp our adopt-a-trail is going to be done for planing of the clean up. And the big one is gonna be in late June up to Hollister Hills for Blazer-Fest. That is gonna be huge this year. Do you think it may be done for that one? If not I'm sure there will be some in July, then August, then September, then........well you get the picture./forums/images/icons/cool.gif
     
  6. mike reeh

    mike reeh 1/2 ton status

    Joined:
    Jul 23, 2001
    Posts:
    752
    Likes Received:
    0
    Location:
    San Diego, CA
    yes im definately going to wheel it!

    ooh blazer fest, Im going to try to make it. If i play my cards right I can easily have the truck going by then. depends on if i want to drag this project out even more.. its getting to the point where im going to be scared to drive it, i have so much $$ and time invested.

    mike
     
  7. mike reeh

    mike reeh 1/2 ton status

    Joined:
    Jul 23, 2001
    Posts:
    752
    Likes Received:
    0
    Location:
    San Diego, CA
    its a 1350

    mike
     
  8. Esteban86K5

    Esteban86K5 1/2 ton status

    Joined:
    Feb 17, 2000
    Posts:
    3,712
    Likes Received:
    0
    Location:
    Bakersfield, CA
    <blockquote><font class="small">In reply to:</font><hr>

    yes im definately going to wheel it

    <hr></blockquote><blockquote><font class="small">In reply to:</font><hr>

    its getting to the point where im going to be scared to drive it, i have so much $$ and time invested

    <hr></blockquote>
    So what's it gonna be!!/forums/images/icons/wink.gif
     
  9. BadDog

    BadDog SOL Staff Member Super Moderator Author

    Joined:
    Feb 24, 2001
    Posts:
    7,777
    Likes Received:
    11
    Location:
    Phoenix, AZ
    Check <a target="_blank" href=http://www.tpijeep.com/1410joint_005.jpg>this</a>. 1410 on the left, 1350 on the right! Someday I want to upgrade to 1350s front and 1410s rear. Or maybe even 1410s front and rear (I don't think I need a CV in front after talking to Jess). When I can afford new shafts...
     
  10. mike reeh

    mike reeh 1/2 ton status

    Joined:
    Jul 23, 2001
    Posts:
    752
    Likes Received:
    0
    Location:
    San Diego, CA
    what did 1410's come in stock?

    that thing is mammoth.
     
  11. BadDog

    BadDog SOL Staff Member Super Moderator Author

    Joined:
    Feb 24, 2001
    Posts:
    7,777
    Likes Received:
    11
    Location:
    Phoenix, AZ
    Not sure, all I know is that you can get yokes for D60/70, C14FF, and front/rear 205. Jess has them all available around $65 each IIRC.
     
  12. m j

    m j 1/2 ton status

    Joined:
    Dec 28, 2001
    Posts:
    4,606
    Likes Received:
    0
    are you asking what 205 came 1410? if so 8?-92 dodge 205s come with 1410 yoke, most likely others as well
     
  13. BadDog

    BadDog SOL Staff Member Super Moderator Author

    Joined:
    Feb 24, 2001
    Posts:
    7,777
    Likes Received:
    11
    Location:
    Phoenix, AZ
    Thanks, now I know where to find 2 of the 4 yokes cheaper, should I stumble onto one in a junk yard between now and when I'm ready for new shafts. Maybe others will have more info.
     
  14. mike reeh

    mike reeh 1/2 ton status

    Joined:
    Jul 23, 2001
    Posts:
    752
    Likes Received:
    0
    Location:
    San Diego, CA
    well thats bogus. I could have gone bigger then? sheeit. Oh well, i really dont think I will break a spicer 1350 w/ 33's. Biggest tire Ill ever run on this truck will be 36's or so and wont see too much hardcore abuse. .. but I wonder how much a 1410 yoke is for the driveshaft, when you go to have the custom shaft made!!

    mike
     
  15. m j

    m j 1/2 ton status

    Joined:
    Dec 28, 2001
    Posts:
    4,606
    Likes Received:
    0
    I have the 1350 at the TC and a 1410 at the dif
     
  16. 84_Chevy_K10

    84_Chevy_K10 Banned

    Joined:
    May 30, 2001
    Posts:
    17,669
    Likes Received:
    0
    Location:
    IL, USA
    New Chevy HDs with manual trannies come with 1410 u joints.
     
  17. Langosta39

    Langosta39 1/2 ton status

    Joined:
    Nov 8, 2002
    Posts:
    156
    Likes Received:
    0
    Location:
    Moscow, Idaho
    Ok, I know enough about most things to get me by, but UJ sizes isn't one of them. Having an 86 1-ton what size do I have? How can I identify them on my truck, just by measuing them?
    andy
     
  18. thatK30guy

    thatK30guy 1 ton status Premium Member

    Joined:
    Jan 12, 2001
    Posts:
    32,076
    Likes Received:
    55
    Location:
    .
    Stock...on an '86 K30, the front will have 1310 series yokes and joints while the rear will have 1350 series. /forums/images/graemlins/wink.gif
     
  19. 84_Chevy_K10

    84_Chevy_K10 Banned

    Joined:
    May 30, 2001
    Posts:
    17,669
    Likes Received:
    0
    Location:
    IL, USA
    Wow, someone's diggin in the archives.
     
  20. m j

    m j 1/2 ton status

    Joined:
    Dec 28, 2001
    Posts:
    4,606
    Likes Received:
    0
    thank you for searching!
     

Share This Page