Dismiss Notice

Welcome To CK5!

Registering is free and easy! Hope to see you on the forums soon.

Score a FREE t-shirt and membership sticker when you sign up for a Premium Membership and choose the recurring plan.

Parts - axle shafts, misc.

Discussion in 'General Parts for Sale' started by Emmettology 101, Oct 15, 2003.

  1. Emmettology 101

    Emmettology 101 3/4 ton status

    Joined:
    May 9, 2000
    Posts:
    8,126
    Likes Received:
    0
    Location:
    FL
    Here what I got:

    2 Pair of 10 bolt front shafts. Both are 28 spline older units. One pair was sitting out so it has rust on the splines. The other pair was in a hosuing sitting out but in decent shape. Both will need joints.
    Good pair - $50 other pair - $30

    Also for same 10 bolt - knuckles, spindles, rotors/hubs, Auto lockouts, open carrier w/2.73's, etc.

    Flat top knuckle from 44(have both sides) - <font color="red">SOLD</font>

    Rear tailpan section for K5. This is just an outer c-channel type piece that repairs rusted ones. Just like stock with tialgate hinge holes - $20

    2wd Steering box - good shape, just needs taped - $50

    35x12.50x15 BFG AT's - low tread - good for spares - $10-20ea. no shipping

    LT1 block - had spun main/rod bearings - make offer
    Rods and pistons from above - make offer

    350 block - has crack in lifter valley but repairable - make offer

    th400 BOP - only about 77K on it - make offer

    NP 208 for 465 - $75

    stock rear d-shaft for 208 to 12 bolt - $25

    Drivers side battery tray - $30?

    Buyer pays shipping... All prices obo... Located in Masury, OH
    Paypal preferred...

    Soon I will have front Superlift Superride springs(6"), D44 parts, 12 bolt shafts, lift blocks etc.....
     
  2. jms

    jms 1/2 ton status Author

    Joined:
    Jan 24, 2001
    Posts:
    1,683
    Likes Received:
    0
    Location:
    --
    Interested in the D44 flat top knuckles - would they fit a on 10-bolt for x-over? Shipping to 68123? Thanks, michael
     
  3. TrcksR4ME

    TrcksR4ME 1/2 ton status

    Joined:
    Feb 11, 2002
    Posts:
    2,482
    Likes Received:
    0
    Location:
    Seattle, WA 98103
    If you end up having any dana 44 axle shafts, I could use the long side with stub shaft, as long as shipping wasn't too outrageous. Thanks
     
  4. Emmettology 101

    Emmettology 101 3/4 ton status

    Joined:
    May 9, 2000
    Posts:
    8,126
    Likes Received:
    0
    Location:
    FL
  5. Emmettology 101

    Emmettology 101 3/4 ton status

    Joined:
    May 9, 2000
    Posts:
    8,126
    Likes Received:
    0
    Location:
    FL
    I do have a 44 under my 82 Jimmy that I may be parting out soon. If I do, I'll let ya know. /forums/images/graemlins/thumb.gif
     
  6. TrcksR4ME

    TrcksR4ME 1/2 ton status

    Joined:
    Feb 11, 2002
    Posts:
    2,482
    Likes Received:
    0
    Location:
    Seattle, WA 98103
    Thanks /forums/images/graemlins/thumb.gif
     
  7. Emmettology 101

    Emmettology 101 3/4 ton status

    Joined:
    May 9, 2000
    Posts:
    8,126
    Likes Received:
    0
    Location:
    FL
  8. sled_dog

    sled_dog 1 ton status

    Joined:
    Sep 3, 2002
    Posts:
    16,870
    Likes Received:
    0
    Location:
    Austin, TX
    Anyword on that parting out D44? i need spring plates for a 1st design D44(2.75 tubes)
     

Share This Page