Roz
1/2 ton status
coral canyon run in a couple weeks too, thats about an hour closer. it has some good beginer to intmediate flex spots. ira and i will be makeing a run when his swap is done
CK5
Register an account today to become a member! Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members.
FarSoCal and AZ
- Thread starter DavidB
- Start date
SchnorrCS
1/2 ton status
where's coral canyon at? Any directions?
K10ANDYKHAMNIC
1/2 ton status
Seach yahoo for it .
DavidB
1/2 ton status
Don't mind my bro. It's 30 mins east from Sandy Eggo. Buckman springs exit. If ya wanna go, holler.
It's 30 mins east from Sandy Eggo. Buckman springs exit. If ya wanna go, holler.Roz
1/2 ton status
about 45 min from downtown SD,8 east to buckmans springs exit. i belive it is the next exit after Vejas casino. let us know if ure interested in a run. lots of trails and flexy stuff 
SchnorrCS
1/2 ton status
I really do wanna go, but I just started a new project with it and gotta finish first....maybe in mid Jan? See if we can get a group to roll or something? I would really like an excuse for the wife to lock up the front end and that may just do.....
Roz
1/2 ton status
im game, just let me know. there is some good mud up there now )
)
SchnorrCS
1/2 ton status
Working on it double time so it should be done sooner.....
K10ANDYKHAMNIC
1/2 ton status
New years was fun at superstitions . AFTER Don left the wind calmed down to nothing .
pismorat
1/2 ton status
I'd be down for a run to Coral Canyon sometime soon...let me know if and when you guys are going.
Roz
1/2 ton status
i go all the time, its everyone else that is party poopers. i tool around with my son mostly, lettting him drive
just let me know and more then likely ill be able to go with ya at least.
just let me know and more then likely ill be able to go with ya at least.
sandawgk5
3/4 ton status
I finally got my rear springs and put my bushing set on order but it is back ordered.
. We can start takin it apart if you want Roz just let me know I do not have duty until mid February. Lookin forward to flexin and not catchin my crossmember
.
Ira
. We can start takin it apart if you want Roz just let me know I do not have duty until mid February. Lookin forward to flexin and not catchin my crossmember .Ira
pismorat
1/2 ton status
I just finished my DIY4X shackle flip, pulled the t-case and replaced the seals and gaskets at the adapter...I noticed that after the shackle flip my d-shaft only has about an inch of compression left could this pose a problem? I might need to go get it re-sized again. After that I should be good to go then...
could this pose a problem? I might need to go get it re-sized again. After that I should be good to go then...Roz
1/2 ton status
ira, im game-just not this weekend. Liz kin in town. but anytime after that is cool. my pay is screwed up again, so i will be spending alot more time at home.
when i did my flip it didnt change much of anything. i still have stock drive shaft
when i did my flip it didnt change much of anything. i still have stock drive shaft
sandawgk5
3/4 ton status
Roz said:
OK I will get with you first of the week and hopefully can just get her on blocks and ready for the install. I think the teardown is the long leg.
Ira
DavidB
1/2 ton status
pismorat said:I just finished my DIY4X shackle flip, pulled the t-case and replaced the seals and gaskets at the adapter...I noticed that after the shackle flip my d-shaft only has about an inch of compression left
SEND IT DOWN
Roz
1/2 ton status
true they do good work
DavidB
1/2 ton status
SOLD the Dodge today - WOOT! Going to Julian tomorrow to pick up the Blazer I'm buying. Then we gotta take Ben to the doc in Sandy Eggo. Whatcha up to tomorrow Roz?
DavidB
1/2 ton status
WAIT a minute! Did I say I was buying a Blazer? Oops! Yeah, right! It's a 4Runner! HAHAHAHA!
Yeah, right! It's a 4Runner! HAHAHAHA!Roz
1/2 ton status
so when do we get to see it?
