dpmalibu
1/2 ton status
Burgandy exterior/interior. Body has a newer paint job from a few years ago. Cab is almost rust free. Rust starting just a little in cab corners.There is a little rust on pass side inner rocker and floor support. Cab is 95% solid. I believe previous owner (owner before guy I bought it from) replaced everything (floors,Rockers, cab corners, doors and fenders. 3" Fibergalss cowl hood(bolt on w/ pins in front).Bed only has rust over the wheel wells on both 1/4's(Bubbling started .Pass side 1/4 has a little rot behind rear wheel.). Bed has bedliner with a huge bed toolbox(could fit a full size floor jack in it w/o handle) mounted at front of bed and diamond plate bed rail caps. All Cab and radiator support mounts were replaced with urethane mounts. Located in Trenton,NJ (609)481-8811
1) Fiberglass cowl hood $200
2) Custom rear bumper w/ drop hitch $75
3) (2) Doors (new) (manual windows) $125 ea. Comes with new mirrors
4) New fenders (2) $75 ea.
5) grill $40
5) headlight bezel trim (plastic) $20pr.
6) windshield $75
7) Rolling chassis w/ cab(with glass) and bed( no doors, seats, steering column,front clip, tailgate, rear bumper) $450 with title.
8) Alpine pull stereo $40
9) Big bedTool box $100
10) set of (4) 454 SS wheels $250
11) 2 1/2" Dynomax w/ dumps $125
12) tailgate $60
13) rear slider glass $50
14) 12 bolt rear w/ 2.76 gears (open diff.)$100
15) Bucket seats (out of late 80's -early 90's Blazer/Suburban) $75
16) center console $ 30
17) overhead console $40
18) 305 motor out of an 87' Trans Am GTA runs good ( mileage somwhere b/t 65k-80k) needs valve seals. $125 for long block
19) factory gauge cluster w/ tach $50
20) Newer Holley 600 Vac. secondaries carb w/ electric choke $150
21) Edelbrock performer manifold center bolts holes were opened up to make it fit an 87-up SBC (Supposed to fit pre 87' SBC) Will still fit older SBC. $40
Make offers on this stuff. Parts need to go. Here is a link to check out pics of truck to see what truck looked like before I stripped it : http://newjersey.craigslist.org/pts/166605664.html
1) Fiberglass cowl hood $200
2) Custom rear bumper w/ drop hitch $75
3) (2) Doors (new) (manual windows) $125 ea. Comes with new mirrors
4) New fenders (2) $75 ea.
5) grill $40
5) headlight bezel trim (plastic) $20pr.
6) windshield $75
7) Rolling chassis w/ cab(with glass) and bed( no doors, seats, steering column,front clip, tailgate, rear bumper) $450 with title.
8) Alpine pull stereo $40
9) Big bedTool box $100
10) set of (4) 454 SS wheels $250
11) 2 1/2" Dynomax w/ dumps $125
12) tailgate $60
13) rear slider glass $50
14) 12 bolt rear w/ 2.76 gears (open diff.)$100
15) Bucket seats (out of late 80's -early 90's Blazer/Suburban) $75
16) center console $ 30
17) overhead console $40
18) 305 motor out of an 87' Trans Am GTA runs good ( mileage somwhere b/t 65k-80k) needs valve seals. $125 for long block
19) factory gauge cluster w/ tach $50
20) Newer Holley 600 Vac. secondaries carb w/ electric choke $150
21) Edelbrock performer manifold center bolts holes were opened up to make it fit an 87-up SBC (Supposed to fit pre 87' SBC) Will still fit older SBC. $40
Make offers on this stuff. Parts need to go. Here is a link to check out pics of truck to see what truck looked like before I stripped it : http://newjersey.craigslist.org/pts/166605664.html
Last edited:
