caveman66
Registered Member
looking for what brand of clutch people are using in there rigs.
and which ones to stay away from
and which ones to stay away from
CK5
Register an account today to become a member! Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members.
Clutches ?
- Thread starter caveman66
- Start date
over the counter 120 clutch kit 11" . fresh cut flywheel. no problems in truck. 1ton 4.10 35" tires tbi feed 350 . i use it for daily drivin/plow 8ft wide/recovery of others/offroad. and i am not nice to it. still goin.
if you have hydro clutch do not use 3 finger pressure plate style. it will not clear the clutch fork. i found out the hard way. had to remove tranny/tcase 2 times.
if you have hydro clutch do not use 3 finger pressure plate style. it will not clear the clutch fork. i found out the hard way. had to remove tranny/tcase 2 times.
I have a 12" Centerforce II in mine and its awesome. Way better than the stock clutch in every possible way.
Luk makes a really good clutch too, and they are about half the cost.
The 11" and 12" clutches use the same flywheel IIRC, I would use the 12" clutch.
Luk makes a really good clutch too, and they are about half the cost.
The 11" and 12" clutches use the same flywheel IIRC, I would use the 12" clutch.
Randy92782
1 ton status
Not sure but i went to Napa and just bought w/e they had
Seems to work just fine for me
Seems to work just fine for me
Disciples Performance
1/2 ton status
depends on the application lol dual centerforce, ACT id say are some of the best LUK clutches ive always had problems with the ex's truck would constantly blow up LUK clutch friction plates and throw out bearings so id stay away from those personally...
if you have hydro clutch do not use 3 finger pressure plate style. it will not clear the clutch fork. i found out the hard way. had to remove tranny/tcase 2 times.
Is this typical? I'm converting to hydro and my clutch is a 3 finger McLeod that I really want to use.
search my name with hydro as the word. i have 2 threads on hydro clutch swap and then problems found. good read for anyone swaping over.
here ya go some good ones.....
http://www.coloradok5.com/forums/showthread.php?t=217368&highlight=hydro
http://www.coloradok5.com/forums/showthread.php?t=193238&highlight=hydro
http://www.coloradok5.com/forums/showthread.php?t=200196&highlight=hydro
http://www.coloradok5.com/forums/search.php?searchid=739909 search for hydro for ya also.
here ya go some good ones.....
http://www.coloradok5.com/forums/showthread.php?t=217368&highlight=hydro
http://www.coloradok5.com/forums/showthread.php?t=193238&highlight=hydro
http://www.coloradok5.com/forums/showthread.php?t=200196&highlight=hydro
http://www.coloradok5.com/forums/search.php?searchid=739909 search for hydro for ya also.
caveman66
Registered Member
thanks for all the info.
blazin_blazer
1/2 ton status
i love the ram ceramic/brass button disk, w/ borg beck pressureplate
walla2k5
1/2 ton status
Centerforce 2,nuff said.
MattK
1/2 ton status
Love my Luk ProGold 12".
Slapperbar
Retired Navy NDT Examiner
10,000 RPM Kevlar Behind a 13:1 350/425/205 and 39.5 swampers. All day on the rocks no problems. We beat it like a red headed step-child too.
chulisohombre
1/2 ton status
i bought the 12 inch napa to replace whatever the p.o. had in there.its been good for a few years now.no problems.i believe they said that it was a luk clutch.had the flywheel reserfaced and that was it.
Not sure but i went to Napa and just bought w/e they had
Seems to work just fine for me
