What's new
CK5
Register an account today to become a member! Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members.

Entire 1989 suburban (partial parted)

mouse

mouse

1/2 ton status
Joined
Nov 10, 2003
Posts
1,447
Reaction score
1
Location
Great Falls Mt
Blue interior, great shape. Electric windows

Trans and TC are SOLD

I would like to sell the entire rolling chassis with the tranny and TC, axles etc. Truck ran great before head gasket blew. Trans and TC are in good shape. Engine is seized, I have not torn it down far enough to find out why yet. - $700 for everything or $350 minus trans and TC. Frame is rust free. Body is almost 100% rust free. Only rust I could fins was minor surface rust on inner fenders and bottom of one barn door.

:
-four-headlight grill/rad support. Grill chrome is peeling/pass headlight bucket cracked. Pending sale
-Overhead console (perfect) PENDING SALE
-Middle fold down seats
-Rear seat
-drawtight receiver hitch SOLD
-spare tire cover
-heater controls (AC)
-All AC components (still has a charge in it now/serpentine system) PENDING SALE
-Cruise control components (control arm on column has been glued together) PENDING SALE
-Misc interior trim (again - blue interior/exterior)
-Doors, hood, front clip. Rust free, can send pics. (I want to wait a month or so before disassembling body so neighbors don't get excited)
-Rear door panels (front door panels pending sale)
-Tub and frame are great shape (no rust), but these would have to be picked up!

Also have a B&M megashifter for sale (not from sub). It was run for 4 months, then pulled. great shape.

-bumpers are bent and not very good shape.
 
Last edited:
Barn doors, but the latch is missing the button and the lock cylinder is gone. They are in great shape, but I can't open them...If you want the tub and frame let me know soon. I have some folks interested in the doors and front clip. The interior is starting to go to.

sub4.JPG
 
I will get the rad support out after I lift out the motor/trans, and am ready to get rid of the truck. I can't dissassemble too much until the very end...so the neighbors don't complain.


bigarmzz said:
let me know about the rad support :confused:
Click to expand...
 
SUB-ZERO said:
Don't suppose you'd ship the barn doors for a little extra $$$?
Click to expand...


Sure, but I haven't been able to open them. The button is missing on the handle, and the lock cylinder is gone. Any Ideas?
 
seconed in line for the doors, what would you want for them?


you cant reach in with you finger to open them?
 
Barn doors are different, you have to pull BOTH rods that go to the top and bottom of the door.
 
Sub zero, make me an offer on the doors. I will get out there and see if I can get them from the inside. It may take a week or more before I can, the weather is not cooperating. Right now its -3 degrees F. It has not been higher than 8 in the last 3 days...
 
have ya been able to get to that rad support yet?

i'm in no hurry, i just dont want to "loose my slot" in line for it :wink1:

snap a pic of it sometime?

thanks alot
 
whats the underhood wiring look like? i need the right side (passenger) side of the underhood harness.
 
bigarmzz said:
have ya been able to get to that rad support yet?

i'm in no hurry, i just dont want to "loose my slot" in line for it :wink1:

snap a pic of it sometime?

thanks alot
Click to expand...


No problem, I got you marked for the rad support. Its been too cold to work on it though...todays high is 2 degrees F...
 
55Willy said:
whats the underhood wiring look like? i need the right side (passenger) side of the underhood harness.
Click to expand...


What do you need exactly? I'm using the engine harness, but the AC part is still available...
 
You must log in or register to reply here.

Latest Posts

Top Bottom