Hollister Wheeling **Pics**

[79chevyk10]

After about 1/2 inch of rain, some friends and I decided to go to Hollister for some fun. Luckily I had a friend ride shotgun that was taking pictures, because I'm bad about that.

Little warm up on Squeeze Rock.

 

[79chevyk10]

More

Then onto Tank Trap. This is the first obsticle on the trail and everyone besides me had to winch up....hehehe. In fact I spanked it so fast that we didn't get any pictures.

 

[blowedupmotor87]

Sweet pics man! That is a bad lookin' truck you've got there!

 

[79chevyk10]

More

Got really friendly with the canyon wall but suffered very little damage. At least no new damage bad enough to notice.

 

[79chevyk10]

More

At this point it was lunch time so we stopped for lunch and took off to run the V's that run besides Bonanza Gulch. Were not able to run the whole trail due to ran out of day light and started to rain again.

Winching was involved by all on this spot. We all ended up on our side.

 

[79chevyk10]

Sweet pics man! That is a bad lookin' truck you've got there!

Thanks. It works really well when it's not broke.

 

[79chevyk10]

Sweet pics man! That is a bad lookin' truck you've got there!

As you ask for in the pm. The pics of the cage.

 

[Stomper]

Nice cv's

 

[GotBoykins]

Nice cv's

X2, and cool pics.

 

[blowedupmotor87]

Dang that's clean lookin', good job man! I like the way you cut the dash cover to perfectly fit, smooth! Thanks for posting those shots up, I appreciate it!

 

[79chevyk10]

Nice cv's

I love those things. Turns soo smooth. Was running Yukon 35 spl outers and stock inner with stock u-joints thinking that was all I needed. Well, I was wrong. Tore the ear off the Yukon which destroyed the u-joint and non-necked down inner. Even though Yukon would warranty the stub. I was left without an inner and needed to buy a new u-joint. So I decided that for an extra 350 bucks over Superiors and ctm's I could go for full bling. Wonder what is the next weak link?

 

[79chevyk10]

Dang that's clean lookin', good job man! I like the way you cut the dash cover to perfectly fit, smooth! Thanks for posting those shots up, I appreciate it!

Hope all goes well with your cage design.

 

[Slapperbar]

Looks good! But the door bar needs to be 12" up higher on the main hoop. Jus' sayin'.

 

[Ten_Bucks]

Nice pics and nice rig! I also like how the A pillar downtubes on that cage go through the dash instead of around the dash.

Scott

 

[79chevyk10]

Looks good! But the door bar needs to be 12" up higher on the main hoop. Jus' sayin'.

My seats are mounted to the "door bar" as you call it. Once I tube out the back half I'm gonna run the hoop behind the cab thru the cab to the cage. Also planning on boat siding also and tie the cage to the frame. Behind the front clip which is skinned is tubed also.

 

[blowedupmotor87]

Hope all goes well with your cage design.

Thanks man! It's gonna be quite a while from now though. Thanks for the cool ideas and the great pics! I like your tubed and skinned frontend treatment too! Looks like you've done a lot of good work!

 

[79chevyk10]

Nice pics and nice rig! I also like how the A pillar downtubes on that cage go through the dash instead of around the dash.

Scott

Less bends equal stronger design and give a clean look that doesn't look "bolt on"
Thaks for the compliments guys, I appreciate it.

When do we have the Blazer Fest (that's in Hollister right) ?

 

[Ten_Bucks]

Less bends equal stronger design and give a clean look that doesn't look "bolt on"

I like that look too.

Scott

 

[silveradoreb]

Sweet truck, I have seen it on pirate...I never realized you had longfields...superbling. Awesome cage too, that is how I plan to do mine.

 

[jk5blazer]

Thats on hell of an expensive beer coaster!!!!!!