Installed Reer Steer today

[1 FN HI K5]

Well i had help today installing my reer steer. Here is a couple of pic's Thanks Tmanofcali,Todd an Mike Click below for 3 new photo's taken today <font color="red">1 FN HI K5 </font color>

 

[thatK30guy]

Can't get in. /forums/images/graemlins/tongue.gif

It says: "A problem has been detected.

You do not appear to be the owner of this album.
Make sure you are logged in."

 

[1 FN HI K5]

well you have to look the old fashion way click below <font color="red">1 FN HI K5 </font color>

 

[SCOOBYDANNN]

Man---That is just beautiful, im gonna go cry now. /forums/images/graemlins/thumb.gif /forums/images/graemlins/pimp1.gif

 

[thatK30guy]

/forums/images/graemlins/thumb.gif /forums/images/graemlins/cool.gif /forums/images/graemlins/thumb.gif /forums/images/graemlins/cool.gif /forums/images/graemlins/thumb.gif /forums/images/graemlins/cool.gif

 

[TONYP]

First gens do it again /forums/images/graemlins/k5.gif

 

[bryguy00b]

thats just fawking AWESOME!! /forums/images/graemlins/thumb.gif

 

[**DONOTDELETE**]

Looks good !! When you coming to install one in my Jimmy?

 

[tmanofcali]

brad, i still think it would look better on my 1 ton!!!

it still looks really weird. did you ever measure your turning radius with just the cross-over? it will be interesting to see what it does now....lol.

it was no problem helping, even though i thought i was gonna get smashed undewr the truck a few times...lol. i know you'll help with my rear disks when i go to do it.

later, todd

 

[FWP]

This is way cool! I have some questions, if you don't mind.

What do you think your total cost is?
What are those little doodads between the ram rod and the tie rod?
In the first picture it looks like a shaft running throught the entire axle, what's the story there?

Man, I wish I could have been there to help, and learn something! This is awesome dude!!!

 

[MEPR]

Thats awsome! /forums/images/graemlins/thumb.gif /forums/images/graemlins/thumb.gif /forums/images/graemlins/thumb.gif /forums/images/graemlins/thumb.gif.
Now you can show those little jeeps what it means to go down a tight trail! /forums/images/graemlins/rotfl.gif /forums/images/graemlins/rotfl.gif /forums/images/graemlins/eek.gif

 

[BorregoK5]

I'd like to see it run on the maiden voyage.. thats extremely impressive!

 

[ChevyHuny]

Wow awsome job you guys. /forums/images/graemlins/laugh.gif That is not something you see everyday.

 

[Twiz]

SWEET!!!!!!!!!!!!!!!

very - very cool!

Details man, details !

 

[yunit]

Looks awesome! Can't wait to see some action pics.

 

[st08x]

bad a$$ job. lets see some off road pics

my K-5
photos.yahoo.com/st08x

 

[1 FN HI K5]

Well i dont want the wife to know how much $$ it cost but its in the middle 4 figure #.And if anyone tells her i will lie through my teeth LOL. In between the ram and tie rod is a ball joint knuckle and a threaded pipe with left hand and right hand threads for the toe in and out.Thanks <font color="red"> 1 FN HI Reer Steer K5 </font color>

 

[rodzzilla]

/forums/images/graemlins/thumb.gif

Saaaawwweeeeeeeeeeeeeeeeeeeeeeeeeeeeettttt.

I am gathering parts to do a 14 bolt rear steer for my crew cab. What are you using to control the rear steer from inside the cab? I am debating between a side to side valve or a small wheel &amp; Valve from a stand up fork lift.

 

[rodzzilla]

That bar is for setting up the knuckles on the same plane so you don't have issues w/ bearings and shafts.

 

[1 FN HI K5]

Im going to use 12 volt silenoids and a spring loaded toggle switch <font color="red">1 FN HI K5 </font color>