i am cleaning up big time. parts for sale starter prices listed. if you dont like it ask with best offer. all parts are plus shipping. pics avalible please include email address.
PRICES INCLUDE SHIPPING . IF YOU DONT LIKE IT MAKE BEST OFFER PLEASE.
1: qty 2 complete sets of 205 frame braces. some need clean and paint. all need bushings. 60.00 each ( 1 ) sold
2: hydro clutch parts. 1 good hose from master to slave. 1 good resivor no inner boot sorry. 1 heat sheild for slave. 1 slave push rod with boot. and 1 used hydro gm fork and piviot ball with wear on them. 80.00 all.
3: brace rod for 400/205 tcase up to the bell housing. 30.00 bucks. sold
4: dana 44 thick diff covers. good used with cover bolts for some not both. 1 has small dent. but no gear contact. 30.00 pair. sold
5: 1 set of dana 44 shafts. no joints. both inners and outers. 50 bucks for both inners & outers. SOLD AND GONE !!!!!
6: dana 44 flat top knuckles. off early ih dana 44 was drum brake and 6 studs on spindles. tie rod enter from bottom side. 85.00 for the pair. casting #s ( c36317 - c36318 ) ( gone to scrap not the good style )
7: 1979 front light harnness was working when parted. also both outer fender side markers and 1 frt lens for turn and both metel housings and gaskets with special screws qty 4. 35.00 bucks all of it.
8: tail gate hinges and piviot points with bolts. 20.00 bucks. this is for you blazer guys wanting to swap in pickup gate. sold
9: 1979 center support with hood latch so you can make your older 73-up to a inside hood pop for more safty. 30.00 bucks.
10: 1 new reman frt drive shaft. closed is 28"ish center of cap to center of back ujoint and open is 31"ish . it has a cv head old first style not flat flange. will need ujoint on axle end. cap was missing when i got it. 135.00 ( sold )
11: 1 set of hd crossmember upper ears for tranny/tcase on 1/2 or 3/4 ton only frames. 30.00 bucks pair.
12: 1 complete some rust 1/2 ton or 3/4 ton hd crossmember for tranny/tcase. if you want the ears only for 30.00 thats fine or complete unit for 40.00
13: w style 1/2 3/4 ton crossmember form mid 80s truck. 40.00
14: dana 44 or corp 10 bolt front drive slugs from a late 70s dana 44. 2 slugs/springs/axle clips/covers. 40.00
15: step side front foot step braces. come off a truck that was converted to utility sides 1 week after purchased from dealer. then stored in barn for years and years. 60.00
16: 2 alt pullys for 2 v belts on them. good for onboard air swaps or other stuff. 25.00
17: 2 4" skyjacker alumin lift blocks 30.00 sold
18: qty 2 raised steering arms for 44/10 axles. 55.00 each ( sold )
19: 1 complete like new never used but installed h.a.d 205 tcase driveline ebrake it. sells on his site for 270 before shipping. i will take 200.00 shipped for this. save some cash and see make it yours. ( sold )
payment info is [email protected] just add part to the notes box in paypal thanks.
PRICES INCLUDE SHIPPING . IF YOU DONT LIKE IT MAKE BEST OFFER PLEASE.
1: qty 2 complete sets of 205 frame braces. some need clean and paint. all need bushings. 60.00 each ( 1 ) sold
2: hydro clutch parts. 1 good hose from master to slave. 1 good resivor no inner boot sorry. 1 heat sheild for slave. 1 slave push rod with boot. and 1 used hydro gm fork and piviot ball with wear on them. 80.00 all.
3: brace rod for 400/205 tcase up to the bell housing. 30.00 bucks. sold
4: dana 44 thick diff covers. good used with cover bolts for some not both. 1 has small dent. but no gear contact. 30.00 pair. sold
5: 1 set of dana 44 shafts. no joints. both inners and outers. 50 bucks for both inners & outers. SOLD AND GONE !!!!!
6: dana 44 flat top knuckles. off early ih dana 44 was drum brake and 6 studs on spindles. tie rod enter from bottom side. 85.00 for the pair. casting #s ( c36317 - c36318 ) ( gone to scrap not the good style )
7: 1979 front light harnness was working when parted. also both outer fender side markers and 1 frt lens for turn and both metel housings and gaskets with special screws qty 4. 35.00 bucks all of it.
8: tail gate hinges and piviot points with bolts. 20.00 bucks. this is for you blazer guys wanting to swap in pickup gate. sold
9: 1979 center support with hood latch so you can make your older 73-up to a inside hood pop for more safty. 30.00 bucks.
10: 1 new reman frt drive shaft. closed is 28"ish center of cap to center of back ujoint and open is 31"ish . it has a cv head old first style not flat flange. will need ujoint on axle end. cap was missing when i got it. 135.00 ( sold )
11: 1 set of hd crossmember upper ears for tranny/tcase on 1/2 or 3/4 ton only frames. 30.00 bucks pair.
12: 1 complete some rust 1/2 ton or 3/4 ton hd crossmember for tranny/tcase. if you want the ears only for 30.00 thats fine or complete unit for 40.00
13: w style 1/2 3/4 ton crossmember form mid 80s truck. 40.00
14: dana 44 or corp 10 bolt front drive slugs from a late 70s dana 44. 2 slugs/springs/axle clips/covers. 40.00
15: step side front foot step braces. come off a truck that was converted to utility sides 1 week after purchased from dealer. then stored in barn for years and years. 60.00
16: 2 alt pullys for 2 v belts on them. good for onboard air swaps or other stuff. 25.00
17: 2 4" skyjacker alumin lift blocks 30.00 sold
18: qty 2 raised steering arms for 44/10 axles. 55.00 each ( sold )
19: 1 complete like new never used but installed h.a.d 205 tcase driveline ebrake it. sells on his site for 270 before shipping. i will take 200.00 shipped for this. save some cash and see make it yours. ( sold )
payment info is [email protected] just add part to the notes box in paypal thanks.
Last edited:
