Parting out '88 K5

[mrk5]

Let me know if theres anything you might want.

Stuff that's already gone or spoken for; tcase, tailgate, front clip, hood, doors, lift, motor, TBI, gauge cluster, and top.

I know that's a lot gone already, but you never know what little things someone might be looking for. Some stuff that's left and I have prices for:

• tilt column (NOT intermittent wipers): $30
• the interior door panels: $10ea
• 700r4 (needs rebuild): $75
• axles (gears unknown): $50ea or will pull shafts $15 per shaft Fronts are SOLD
• rear seat: $20
• 10,000# Reese receiver hitch: sold
• rear driveshaft: sold

I also have these to sell:

• TH400 needs rebuild, works but slips badly: sold
• NP203 27-spline tcase w/shifter & adapter unknown condition: $50 pending

 

[oatsk5]

scott that will work on my 75 right rr i think i want it oh yeah the hitch

 

[TDAWG1]

Are those Heads any good?

 

[TDAWG1]

What is the Lift on there I might be interested in that rear shaft too

 

[Cmoe]

Bump ya... Wish you were in AZ or near a friend in CO I would take the front seats....

 

[mrk5]

scott that will work on my 75 right rr i think i want it oh yeah the hitch

Erv, I'll measure it for you when I get to work.

 

[mrk5]

What is the Lift on there I might be interested in that rear shaft too

The heads along with the rest of the motor is spoken for. Jiminycricket is getting the lift.

The rear driveshaft is available: $30 It's a slipyoke style for a 208

 

[mrk5]

Bump ya... Wish you were in AZ or near a friend in CO I would take the front seats....

Harley (Hossbaby50) lives 15minutes from me. He's bringing the tcase from this truck to Marv. You did notice the drivers seat is pretty tore up? The passenger seat looks good.

 

[muddybuddy]

What is the Lift on there I might be interested in that rear shaft too

he ment how much lift does it have for measurements so he knows if he wants the driveshaft or not

 

[Cmoe]

Yah, I saw the drivers seat... What do you want for the pair? I'll have to PM Harley (Hossbaby50) and see if he can bring them down too?

 

[mrk5]

he ment how much lift does it have for measurements so he knows if he wants the driveshaft or not

I knew that! I was just playing dumb to build suspense!

It's standard factory length. I can't remember right-off what that was, but I checked it against mine. 29.5" IIRC to the center of the u-joints.

 

[mrk5]

Yah, I saw the drivers seat... What do you want for the pair? I'll have to PM Harley (Hossbaby50) and see if he can bring them down too?

$30 for the pair.

 

[TDAWG1]

he ment how much lift does it have for measurements so he knows if he wants the driveshaft or not

thanx its nice to be understood every now and again

 

[grimjaw]

Are you willing to ship? If so, I am interested in the transmission. I have a few questions so I will PM you.


"700r4 (needs rebuild): $75"

 

[79Stomper]

I am interested in the body mounts, cups, and washers if you wouldn't mind shipping them. Don't need the bolts to the body.


James

 

[mrk5]

Are you willing to ship? If so, I am interested in the transmission. I have a few questions so I will PM you.


"700r4 (needs rebuild): $75"

You got PM.

 

[mrk5]

I am interested in the body mounts, cups, and washers if you wouldn't mind shipping them. Don't need the bolts to the body.


James

How about $40 plus the ride?

 

[79Stomper]

Sending a PM..

 

[mrk5]

I added a tranny and tcase to the list.

 

[BLZN4FN]

How is the floor in the far back where the rust out most of the time? Or can I cut a few sections of the floor to repair my K5