What's new
CK5
Register an account today to become a member! Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members.

Pro jection help

4

468k5

1/2 ton status
 Premium
Joined
Jul 28, 2004
Posts
141
Reaction score
0
Location
SE Mn.
I pulled a Holley pro jection set up off my buddies truck about a year ago and now I'm finally getting around to putting it on another. I had all the wires labeled and know where to run them except for the pink one. I hadit labeled "starter" but the ring terminal is cut off. Not sure if it goes to the battery terminal or the switch terminal.
Any ideas?
 
shoot me an email and I'll shoot you the owners/installation manual or you can still get it off HOlleys webpage but if I member correctly it was a pain it the butt to find. let me make sure I have it here at home. seems I do. IF you have the 4di setup I have the original holley disk with software and base maps on it also that I could accidently send you copies of if you are in need of em the install manual is 2.5 megs
[email protected]
 
hold on a minute let me grab the manual. one black box is a MAP sensor you got any instant msg programs I think I still have icq loaded and we can go over this in real time
 
sorry afeter disk crash don't have any installed so here it goes:
brown, black/white = coolant temp
red, red, green/black, green/black fuel pump relay
red, red, black, red/wht ignition relay
green, green to db 9 computer
blue/white, yellow/black, red, black distributor
blue, black, red, green, white calibration module (not used on my setup with DI interface)
black with fuse holder 12v source think this was a misprint as my black doesn't have a fuse holder on it
orange red/black, blk/white MAP sensor
wht/brwn, white/Blu, white/grn, white/red, red fuel injectors
purple/yellow, purple blk, purp/blue, purp/white IAC motor
black/white, blue air charge temp
orange, green, blk/wht TPS
red, blk, wht O2 sensor
Those are the connectors now for bare wires
blk ground
red with fuse attach to batery
red/white switched ignition, positive side of coil
yellow ignition/tach negative side of coil factory ignition
yellow/black ignition/tach aftermarket ignition only
orange/red oil pressure switch
wht/red negative ignition coil (di systems that are using spark control only)

that's from the manul I can extract a few pages for you if need be
 
wow yours must be alot newer than this one! mines closer to the one in the link I posted
 
just a thought, does the pink wire run off one of the relays? if so it may be hot wich one could achieve by going to the starter though can think of better places, or it could be the extension to go back to the fuel pump
 
possibility I just went to the Furd page you referenced and it's for projection mines for the projection Di setup sorry if I'm not being helpful but you should try and type all those wires/colors with a squirmy 21 month old in your lap :)
 
no relays at all on this at all. the fuel pump feed is a two wire(red&green) weatherpack connector
 
might trace the wire back some into the loom and see if someone spliced it on to a different color. Is yours projection. projection D, or projection Di?
 
this is what I found out about the black box/o2 sensor "early analog 2D systems used the O2 sensor to modify the TPS signal to the ECM. Its wired into the TPS signal so that the O2 sensor changes the TPS signal to keep the AFR at 14.7."
 
I guess I'm not really sure what version it is, it's not mine.
 
cant view pic not a payed member yet:o, hopefully next payday, house payment due outta thisun, and seems I have time for the board at night now though not to work on truck
 
You must log in or register to reply here.

Latest Posts

Top Bottom