CK5
Register an account today to become a member! Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members.

1982 K3500 - Aurora?

Wes is meaning what you’re calling “Low” as first gear.

GM started calling the actual 2ND gear “first gear” because the general public couldn’t wrap their heads around generally starting out in second gear.
So they labeled the gear shift knob as such.

But the reality is that the transmission has four forward gears so it’s a “four speed” transmission - and the first gear is known as a “creeper” or “crawler” or “granny” or “mule” or “low” gear that is not usually needed during regular driving conditions.
So the 2ND gear ( 3.58:1 ) is used to start off with when the advantage of a super low gear ( 6.55:1 ) is not needed.
To avoid confusion for those who don’t understand this GM just decided to list 2ND gear with a “1” to avoid any issues or complaints.
 
Wes is meaning what you’re calling “Low” as first gear.

Thanks @tarussell !! I was having trouble getting it into 2nd gear (bottom-left). I had to really muscle it to get it to go.

I have only used 1st gear (on my other K30) one time. I used the truck to pull a big plant out of the ground. It was satisfying.
 
Thanks @tarussell !! I was having trouble getting it into 2nd gear (bottom-left). I had to really muscle it to get it to go.

I have only used 1st gear (on my other K30) one time. I used the truck to pull a big plant out of the ground. It was satisfying.
As mentioned earlier above you might be having pressure plate troubles or it may just need adjusting.
2ND gear is synchronized and it should take a slight bit of effort to fall into gear but nothing like having to force it.
The SM-465 is an absolute purpose built truck type transmission and it will never shift as nice and easy as a passenger car trans will but nowhere near the level of straining to shift - ya’ gotta get this looked into so no unnecessary issues arise.
 
I pulled the shifter on Saturday. The factory tack welds are broken on it and the roll pin is super loose. I don't have a welder, but my buddy has the cheap HF unit at his place. I am assuming that even the most novice welder could re-melt the factory tack welds so that they're repaired.

For the roll pin, I would still like to try the plumbers strap trick that was mentioned a few posts back.

Here is a video of the shifter. Be warned that I am listening to loud music in the video, so you might mute it if you watch:

View attachment IMG_1213.MOV

Here is a picture of where my clutch pedal adjustment sits right now... it feels pretty good inside the truck (i.e. I think I have about 1.5"-2" of pedal travel before the clutch is engaged). I need to do another test drive before adjusting it further but I am hopeful I can make it even longer to help the clutch disengage.

IMG_1216.jpeg

After this I put everything back together and got into troubleshooting headlight issues. I think after repairing the tack welds I might go for another test drive and see if the clutch pedal rod needs more adjusting... then it's time to take it to Denver's emissions testing facility.
 
Is there any freeplay (slop) in the linkage?
You basically want all the slack out you can get but not to the point where the throw-out bearing is tight against the pressure plate fingers.

Good point Eddie I bet there is a ton of play in the linkage also. I will try and tighten all of that up too.

I was having a hard time visualizing all of this from end-to-end and found this nice GIF on Google:

View attachment clutch.mp4

EDIT: I am reading about this more online and am wondering if the return spring is worn out also. Will take a peek at that.
 
Good point Eddie I bet there is a ton of play in the linkage also. I will try and tighten all of that up too.

I was having a hard time visualizing all of this from end-to-end and found this nice GIF on Google:

View attachment 539302

EDIT: I am reading about this more online and am wondering if the return spring is worn out also. Will take a peek at that.
Sounds like you’re on the right track.
 
Good point Eddie I bet there is a ton of play in the linkage also. I will try and tighten all of that up too.

I was having a hard time visualizing all of this from end-to-end and found this nice GIF on Google:

View attachment 539302

EDIT: I am reading about this more online and am wondering if the return spring is worn out also. Will take a peek at that.
One spring iirc is between the clutch fork and z bar arm the holds the fork rod. Another from the z bar to the truck frame and the hood style spring under the dash to pedal
 
Top Bottom