Just like the title says looking for a left and a right side let me know what you have.
Last edited:
CK5
Register an account today to become a member! Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members.
4wd forward rear spring hanger
- Thread starter Babaganoosh
- Start date
5wd 
and what frame do you need them for ?
blazer / 1/2 - 3/4 ton or 1ton truck .
and 2wd short or 4wd tall .
and what frame do you need them for ?
blazer / 1/2 - 3/4 ton or 1ton truck .
and 2wd short or 4wd tall .
Darn phone for a 4wd k10 or k20.
These will go on my c10 frame for the 4wd conversion. I need the tall ones.
These will go on my c10 frame for the 4wd conversion. I need the tall ones.
fyi holes for rivits wont line up if I recall.
I know 1tons the 2wd to 4wd holes don't line up .
I know 1tons the 2wd to 4wd holes don't line up .
Hmmmm maybe someone can measure for me if they would.
oh they fit just got to redo holes if I recall.
with your build I think you can handle this .
with your build I think you can handle this .
Shouldn't be a problem but would like to know.
I have a set you could borrow until after Blazer Bash, but I don't know if that really does you any good.
I have a set of these laying around. Came off of 79 k20. Give me a chance to find them and make sure I still have all the pieces and Ill post up some pics. If I remember right they have some rust, maybe a little pitting but no holes. Id let them go cheap too but like I say let me get them dug up and get some pics up for you.
And no the holes don't line up so youd have to drill new ones.
And no the holes don't line up so youd have to drill new ones.
How bad are they? The rest of the truck is rust free.
So I am about to send a suburban to the crusher. I hate to,,, but my Dad bought it for the trans. Anyway I could send you some pics to see if you would like these. Sending you a PM
They are not bad. I pulled them out today and made sure everything was there still. Got some pics Ill upload when my wife gets home and tells me where she hid my cord
But they aren't bad, personally I would brush the rust off, paint them and run them on anything I own but they definitely don't look "new". Might be able to smooth them out with a flapper wheel or something, the pitting is very light.
Ill get the pics of them up later and you can give me an offer if you want them.
But they aren't bad, personally I would brush the rust off, paint them and run them on anything I own but they definitely don't look "new". Might be able to smooth them out with a flapper wheel or something, the pitting is very light.
Ill get the pics of them up later and you can give me an offer if you want them.
Tried to get some good close ups of the rust but my old school razor camera isn't up to par with the I-phone 5
This one shows the worst of the rust. Its the brace that goes under the frame rail looking at the bottom side
I only got pics of one side cause the other is still attached to a spring pack that I didn't know I had but both sides are in similar condition.
Like I said if you want them just make an offer. Don't need the money, don't need to get rid of them but I really don't need them either, just trying to help out.
This one shows the worst of the rust. Its the brace that goes under the frame rail looking at the bottom side
I only got pics of one side cause the other is still attached to a spring pack that I didn't know I had
but both sides are in similar condition.Like I said if you want them just make an offer. Don't need the money, don't need to get rid of them but I really don't need them either, just trying to help out.
