Sorry, I did not see your last post about not being angry. Dial-up sucks at work.
CK5
Register an account today to become a member! Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members.
Blazen off road Rear tube bumper
- Thread starter Blue90
- Start date
Blue90
1/2 ton status
- Joined
- Aug 27, 2004
- Posts
- 583
- Reaction score
- 2
BulldogK5 said:Give it a little more time. He could be out testing and improving this week. I'm not trying to make excuses either but it could be as simple as a wrong label and you got one for somebody else who has a 1-2" body lift.
In the meantime, you might try and remove some of these negative waves. Jesse will make it right.
Yeah it's all good I know, I'm not really trying to start a rant here. More or less just get some feed back from you guys.
Wait until Monday for him to reply back.... I hear Jesse is at Blazer Fest this weekend.
And yes, I agree with Pauly383 on the rear quarter panels. They do look like they need to be cut back.
And yes, I agree with Pauly383 on the rear quarter panels. They do look like they need to be cut back.
chevysmithz71
1/2 ton status
I know Exactly why he is not answering. He is wheeling this weekend At Blazerfest in Hollister, Ca. He probably got there thur. so he has been loading a getting ready for a few days before that. I am going there tomorrow morning and Ill mention it to him.
Very stand up guy will get it taken care of.
Very stand up guy will get it taken care of.
81jimmyslt
1/2 ton status
Well there we just got back from Blazer Fest in Hollister Hills for the weekend.
As for the voice mail and email, we did not have great reception in Hollister unless we drove into town. We are back at the shop and office all week so call we will pick up.
As for the bumper, It looks like we must have nmentioned you do not need to cut or weld to install this bumper, our mistake!!! The rear tube bumpers have side impact bars that sit right at the rear lower fender, these need to be trimmed to increase your side clearance. The bumper can be made without the side impact bar but the rear fender will still hang down below the bumper.
As for the bumper hitting the tailgate and the gas tank skid plate, it should fit like a glove if it is pushed all the way on, it is resting a few inches forward because of the rear fender.
We are going to change our online description of this bumper to make sure it reads minor trimming is required if you want the side supports.
We will be giving you a call this morning so we can clear this up for you.
Here is Smokkey1's experience with our rear bumper....... http://coloradok5.com/forums/showthread.php?t=171650&page=18&highlight=smokkey1+bumper
Thanks,
Jesse Kruger
www.blazenoffroad.com
[email protected]
530-416-7902
As for the voice mail and email, we did not have great reception in Hollister unless we drove into town. We are back at the shop and office all week so call we will pick up.
As for the bumper, It looks like we must have nmentioned you do not need to cut or weld to install this bumper, our mistake!!! The rear tube bumpers have side impact bars that sit right at the rear lower fender, these need to be trimmed to increase your side clearance. The bumper can be made without the side impact bar but the rear fender will still hang down below the bumper.
As for the bumper hitting the tailgate and the gas tank skid plate, it should fit like a glove if it is pushed all the way on, it is resting a few inches forward because of the rear fender.
We are going to change our online description of this bumper to make sure it reads minor trimming is required if you want the side supports.
We will be giving you a call this morning so we can clear this up for you.
Here is Smokkey1's experience with our rear bumper....... http://coloradok5.com/forums/showthread.php?t=171650&page=18&highlight=smokkey1+bumper
Thanks,
Jesse Kruger
www.blazenoffroad.com
[email protected]
530-416-7902
Last edited:
chevysmithz71
1/2 ton status
Now that's customer service!!
