I scored too! '82 k3500

[RoTuN]

Get a sharpie, mark one spline. That is spline zero. Count ten, mark the tenth spline, count ten, mark till you go all the way around. The "zero" spline become the final spline. That is your spline count. I usually counts in two with smaller marks that way if I make a mistake, it is easily spotted.

When I worked nights, I had to double check the first article off the gear cutter. It get real easy to get lost counting 153 teeth. If you mess up, you have to start over.

Thanks for the tip, I did mark my starting point but it was on the ground, getting dark and I was about worn out so I decided to count them tomorrow. Couldn't imagine having to count 153 teeth!

 

[RoTuN]

Doing some research on this 454, turns out it is a gen V, possibly a gen VI. But can't find any specs re: hp and torque. Still have to get the numbers off the heads then I can decide f.i. or carb.

 

[Zeus33rd]

Doing some research on this 454, turns out it is a gen V, possibly a gen VI. But can't find any specs re: hp and torque. Still have to get the numbers off the heads then I can decide f.i. or carb.

According to this link-

http://www.offshoreonly.com/forums/general-q/104711-chevy-v-8-casting-numbers.html

It's a Gen V or if it has the fuel pump boss, Gen VI

340220.....427T......68-85...4-bolt
345014.....454.......70-86...
346236.....454.......75-76...2-bolt
359070.....454.......70-90...
361959.....454.......73-90...2 or 4 bolt
364776.....427T......68-85...4-bolt
364779.....366T......68-90...4-bolt
399204.....509.......70-71...4-bolt, Alum., CanAm, 4.5" bores, Cylinder liners
399289.....454.......73-79
399293.....366T......77-78...4-bolt
473478.....427T......77-90...4-bolt
3782870....427T......68-76...4-bolt
3824553....366T......66-67...4-bolt
3855961....396.......65-66...2 or 4 bolt
3855961....427.......66......2-bolt
3855962....396.......65-66...4-bolt
3855977....366T......66-73...4-bolt
3869942....427.......66-67...2 or 4 bolt
3902406....396.......67......2 or 4 bolt
3904351....427.......67......2 or 4 bolt
3904354....366T......66-76...4-bolt
3916319....366T......68......4-bolt
3916321....427.......68......2 or 4 bolt
3916323....396.......68......2 or 4 bolt
3925521....427T......68-85...4-bolt
3935439....427.......68-69...2 or 4 bolt
3935440....396.......68-69...2 or 4 bolt
3937724....366T......68-85...4-bolt
3937726....427T......68-84...4-bolt
3946052....427.......69......4-bolt, Alum. ZL-1, Mark IV
3946053....427.......97......4-bolt, Alum. ZL-1, 2nd version, Mark IV
3955270....427.......69......2 or 4 bolt
3955272....396.......69......2 or 4 bolt
3955274....366T......68-85...4-bolt
3955276....427T......68-73...4-bolt
3963512....427.......69......2 or 4 bolt
3963512....454.......70-76...2 or 4 bolt
3969852....366T......68-84...4-bolt
3969854....396.......69......2 or 4 bolt
3969854....402.......70-72...2 or 4 bolt
3969858....427T......68-84...4-bolt
3999289....454.......72-79...2 or 4 bolt, some "CE" replacement blocks had four bolt main caps
3999290....396.......68-69...2 or 4 bolt, Truck
3999290....402.......70-72...2 or 4 bolt, Truck
3999290....402.......72......2 or 4 bolt, Passenger
3999293....366T......68-90...4-bolt
3999294....427T......68-84...4-bolt
10051107...454...............4-bolt, Bowtie, MkIV, 9.8" deck, siamesed cylinder barrels, 4.25" semi-finished bores, can be bored to 4.50"
10069282...366T......90-91...4-bolt, Mark IV, Tall deck
10069284...427T..............4-bolt, Mark IV, Tall deck
10069286...454.......90-91...4-bolt, Mark IV, Short deck
10114182...454.......91-up...4-bolt, Gen.V
10114183...366T......91-up...4-bolt, Gen.V
10114184...427T......91-up...4-bolt, Gen.V
10134366...454T..............4-bolt, Bowtie, Gen.V, Tall deck
10185050...454...............4-bolt, Bowtie, Gen.V, Short deck
10237297...454.......96-up...4-bolt, Vortec 7400", "L-29" Gen.VI
10237300...502.......96-up...4-bolt, Gen.VI, 4.466" bore
12550312...427T......96-up...4-bolt, Gen.VI, 4.250" bore, fuel pump boss, clutch linkage pivot boss
12550313...454.......91-up...4-bolt, Gen.V crate motor, Gen. VI 4.25" bare block, fuel pump boss
12556110...496.......01-up...4-bolt, Gen.VII 8.1L, "Vortec 8100", Truck
12561357...454.......96-up...4-bolt, Gen.VI
12561358...502...............4-bolt, Gen. VI
14015443...454.......87-90...2 or 4-bolt, Mark IV, Truck, Motorhome
14015445...454.......78-90...2 or 4 bolt
14044807...454T..............4-bolt, Bowtie, MkIV, CNC prep, Tall deck, 4.25" bore or 4.495" bores
14096859...502...............4-bolt, Gen.V, HO
24502504...454...............4-bolt, Bowtie, Gen.V, Race prep, 9.8 "short" deck height
24502506...454T..............4-bolt, Bowtie, Gen.V, Race prep, 10.2 "tall" deck height
24502572.....................4-bolt, 4.5" bore Olds DRCE 2, 9.5" deck height
25534402.....................4-bolt, 4.590" bore Olds DRCE 3, 9.25" deck height


Great score on the truck.

 

[RoTuN]

Thank you, found that info as well. It does have the fuel pump boss and the external oil cooler provision. I need to get the #'s off the heads...this might even be a 454 HO.

 

[RoTuN]

Turns out it is not a HO, oh well. The inside is pretty clean, taking to the shop to get tanked so I can paint it. Also going to get the "California cam" replaced with something a little lumpier and different heads.

 

[RoTuN]

Well, broke out the industrial strength, acid based de-greaser and the pressure washer today......................have to love the "corrosion inhibiting characteristics" of the diesel engines, everything was coated with at least a 1/4" of grease/ oil. Found some factory markings underneath all of it.