CK5
Register an account today to become a member! Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members.
is this a dana 60?
- Thread starter wazzabie
- Start date
Yep, kingpins are a dead give away...
COCHEV
1/2 ton status
...and go get it...NOW! That's a steel
better grab the th400/203 for a doubbler kit later. as its got full time drive slugs on it.
chulisohombre
1/2 ton status
yep and a pretty good price.go pick it up before someone beats you to it.
The problem is that I have no way of getting it home. I'm about 1.5 hrs away. If I had the K5 running would it be possible to tear the dana 60 down and carry it in the back of the K5? I also have a honda but I don't think it would fit even if it were completely torn down. I need tires for my K5. So if I buy 1/2 ton tires then I would need to sell them to get the 1 ton tires. I need to get a truck so I can hull the axels for my K5 build.
Yes, you could pull it apart and get in a K5, no way on the Honda though.
Find a friend with a pickup
Find a friend with a pickup
cegusman
3/4 ton status
Not true. I put a 14bolt ff in a 3 door Saturn. with a SM465/np203 in the trunk. Took the passenger seat out and put the axle in piece by piece.
mr250twostroke
1/2 ton status
Gears? Have you called on it? Not enough info to say that's a great deal... Having said that I'm right up the road from graham, would haul it for expenses and a case of Pacifico...
I just called him. It is sold. He had 4.10s in it. Was that a good deal? Thank you for the kind offer mr250twostroke. Maybe I could take you up on this next time.
mr250twostroke
1/2 ton status
Were you looking for 4.10's? Sounds reasonable to me. I probably know the person that bought it. When you know what your looking for (gears) and are ready let me know, I can give you some good contacts. Lots of wheelers down here who buy and sell.
I'm not sure what gears I would need. I think the 4.10s are the most common. I would like to run 35s with out fear of breaking an axle. Currently I have the dana44 and the 12 bolt rear. It is all stock 1/2 ton stuff. I have some old school turbine rims that fit a one ton I would like to use. They are the 16.5 rims. After breaking the NP203 I replaced it with a NP205 from a 72 K5.
That would have been a great deal, with OEM drive slugs to boot!
dirtygoat
1/2 ton status
Dustin, Casey called on it also and it was gone... Odie might have gotten it though...
It was just down the road from me...
It was just down the road from me...
mr250twostroke
1/2 ton status
I figured Odie or Corey snatched it. They're C L ninjas...
I drove from SLC to Boise for a $600 Dana 60 (gas was free and had a place to stay)
... now there all over for 6-800
... now there all over for 6-800
The price was a little high, im eyeballing a complete truck for about the same price. If odie got it, he probably offered $200
mr250twostroke
1/2 ton status
The price was a little high, im eyeballing a complete truck for about the same price. If odie got it, he probably offered $200
At least I'm not the only one that didn't think it was an amazing deal. Odie's probably in Laughlin or somewhere sunny anyways...
The price was a little high, im eyeballing a complete truck for about the same price. If odie got it, he probably offered $200
That is my thoughts also. I would need to get a 14 bolt plus the TH400/ NP205 setup. So in the end it may be cheaper to but a 1 ton parts rig then just the dana60.
btw - Is there any K5 meetups down your way? It seams like there are several of us in the puget sound area on this board.
