63chevyll
1/2 ton status
I have JB weld on the side of ny Toyota block..... Been there for 14 years. That **** works, but for stock tabs, he has got to be full of it.
CK5
Register an account today to become a member! Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members.
JB welded spring plates?!
- Thread starter Kocher93
- Start date
I wonder if he cleaned it down to bare metal before doing the JB Weld 
dirtygoat
1/2 ton status
There is so much win in this thread...
I might build some link mounts out of JB Weld tomorrow...
If I have some time, I'll start on a crossover steering arm...
I might build some link mounts out of JB Weld tomorrow...
If I have some time, I'll start on a crossover steering arm...
Duh, everyone knows you make roll bars out of PVC pipe. That copper stuff is too expensive.
TheBeast_88K5
Banned
Shoulda bi*** slapped him right there and called johnny law before somebody (most likely an innocent bi-stander) gets killed. I wouldnt have worried about how much it may have insulted him, he deserves it and you shoulda stole his keys too lol
With as many junk parts as people have lying around might be a fun project to try. JB weld it up then see how hard it is to break. It's not something I would do on my truck. But if I had an old junky truck to try it on it might be fun. Assuming it was never driven on a public road.
TheBeast_88K5
Banned
Can we pleeeeease just let natural selection take it's course...
You SHOULD HAVE asked him to go wheeling!
Shame on you....
You SHOULD HAVE asked him to go wheeling!
Shame on you....
Can we pleeeeease just let natural selection take it's course...
You SHOULD HAVE asked him to go wheeling!
Shame on you....
Winnah, winnah, chicken dinnah.
wasted wages
1 ton status
I'm callin' B/S on this whole thread......
ain't no way J/B weld is going to keep a rear axle from turning in the spring saddles under torque or braking.......I don't care how tight the ubolts are......
And shock mounts....... come on.... be real.
J/B weld is nothing more than epoxy with a little metal dust mixed in.....
maybe he put J/B weld over his ****ty welds so no one would see them....
ain't no way J/B weld is going to keep a rear axle from turning in the spring saddles under torque or braking.......I don't care how tight the ubolts are......
And shock mounts....... come on.... be real.
J/B weld is nothing more than epoxy with a little metal dust mixed in.....
maybe he put J/B weld over his ****ty welds so no one would see them....
I'm callin' B/S on this whole thread......
ain't no way J/B weld is going to keep a rear axle from turning in the spring saddles under torque or braking.......I don't care how tight the ubolts are......
And shock mounts....... come on.... be real.
J/B weld is nothing more than epoxy with a little metal dust mixed in.....
maybe he put J/B weld over his ****ty welds so no one would see them....
I bet thats what he did, put it over ****ty ass welds
TheBeast_88K5
Banned
Maybe you misunderstood.....
Maybe his freind "JB" welded it...
Maybe his freind "JB" welded it...
GMCSuburban2500
Registered Member
Maybe you misunderstood.....
Maybe his freind "JB" welded it...
Probably the case.
Seriously though, I can't imagine anybody doing that for real... JB Weld is neat stuff, and certainly has it's place, but as has been mentioned, it's just epoxy. Probably burned a hole in the axle tube welding and covered it with JB Weld...
63chevyll
1/2 ton status
Maybe he is frineds with Justin Bieber and he welded it....
Kocher93
1/2 ton status
There was definantly a large amount of jb weld in and around the spring plates and flowing down the axle, I didn't get a look at the shock tabs, but I think jb could hold a shock tab on, depending on how worn out/soft they are.
TheBeast_88K5
Banned
I'm subscribing. Now I wish I had the time to JB weld some spring plates on my old 12 bolt and see if it holds
