now open workcenter pics.
CK5
Register an account today to become a member! Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members.
new snap-on tool box build up .... version o.75% build up has begun
- Thread starter sweetk30
- Start date
and few more for good tastes
It is a thing of beauty, enjoy!
readymix
3/4 ton status
Tell me about that air tool holder please.
Link and or a closer picture would be great.
Link and or a closer picture would be great.
new off truck around 60-65 bucks. i wouldnt pay that much. so i went to ebay and found them here for better price.
http://cgi.ebay.com/ebaymotors/ws/e...STRK:MEWA:IT&viewitem=&item=120137947258&rd=1
its o.k. only major problem was need teflon tape to seal the fittings to there hanger fittings good. little short on the machining but love it other than that. makes life at work much better. thats after 1 days use only.
http://cgi.ebay.com/ebaymotors/ws/e...STRK:MEWA:IT&viewitem=&item=120137947258&rd=1
its o.k. only major problem was need teflon tape to seal the fittings to there hanger fittings good. little short on the machining but love it other than that. makes life at work much better. thats after 1 days use only.
readymix
3/4 ton status
Does it only work with the swivel adapters?
its not a swivel persay. its just a bulge fitting to hang buy.
i can get closeup pics tusday and post tusday night for ya. let me know.
i can get closeup pics tusday and post tusday night for ya. let me know.
Confedneck79K30
3/4 ton status
SEXY!!! clean and sharp!!
readymix
3/4 ton status
Please do.
I was thinking about just buying a piece of angle and bolting some fittings to it. but if I could make one that would allow me to remove the tools with one hand.....that would be perfect.
I was thinking about just buying a piece of angle and bolting some fittings to it. but if I could make one that would allow me to remove the tools with one hand.....that would be perfect.
camera is with wallet for trip to work in the am for your pics.
and just lift a bit and slide out the slot and go 1 handed. its a nice setup.
and just lift a bit and slide out the slot and go 1 handed. its a nice setup.
here ya go readymix. pics you asked for.
readymix
3/4 ton status
so is that a swivel or just an adapter required to work with the holder?
just a inline spacer to bulk up to the bubble that it looks like to hang on the rack. not a swivle.
readymix
3/4 ton status
Thanks for the pics. I think I could make something like that.
Not sure why I never though of doing it like that before.
Not sure why I never though of doing it like that before.
DEMON44
Low-Tech Redneck
anyupdates to throw down on the 1033? love it?
snapon here has a deal on boxes right now.and I can get more than I paid for my Mac box as a trader to. so I'm thinking hard about a 1033.
snapon here has a deal on boxes right now.and I can get more than I paid for my Mac box as a trader to. so I'm thinking hard about a 1033.
Confedneck79K30
3/4 ton status
do it, you've never had a box you could fit a 58" prybar in until now
love the box all the way to the bank. and like said nothing like putting your longest tools in the box and not out side someplace.
you will be happy with the snapon box quality. i have had my hand on most brands and nothing comes close to snapon boxes.
take a few min and look here and watch the viedos . http://www.theundisputedchamp.com/
only thing i am going to get next is a bulk end locker krl1012 . and then later i will get a 1018 docker locker.
left is 1012 locker right is 1018 docker locker with cart.
you will be happy with the snapon box quality. i have had my hand on most brands and nothing comes close to snapon boxes.
take a few min and look here and watch the viedos . http://www.theundisputedchamp.com/
only thing i am going to get next is a bulk end locker krl1012 . and then later i will get a 1018 docker locker.
left is 1012 locker right is 1018 docker locker with cart.
Confedneck79K30
3/4 ton status
smart moves, then the only way to go is up, with overheads
