parting my truggy

[yunit]

Parting Truggy:

Attempting to take a step back and building the rig I originally wanted; which is not as modified as my Truggy has become. All prices are firm and the buyer has to pay for shipping. Please email me with any questions or interest that you might have. Thanks, Pete.

[email protected]

4 - 42x15x15 TSL's 90% tread & 1 - 42x15x16.5 TSL spare with 8 lug white wagon wheel $900, $1000 with rims below) or trade for a set of 36 or 37" tires with 17" wheel size.

4 - 15x10 / 4.125" backspaced 8 lug ARE wagon wheels (the ones in the picture) $150


SOLD
Front Alcan springs, 6" lift, 49" long, move axle 2" forward (need to move spring buckets forward), come with prothane spring bushings $300

Rear Alcan springs, 2" lift, 57" long, move axle back 3", come with Prothane bushings $300
***The springs have one trail ride and have mainly been used to hold what is left of the truck up.

ORD 4" shackle flip for 73-91 K5's & 73-87 pickups $SOLD

Package deal: (Less then 20 miles on this whole package)
-TH400 built by Level Ten with PTS manual valve body, Chrysler filter modification, and Level 10 PTS 1600 stall convertor...good for 900HP.
-ORD Gen II Aluminum Doubler setup with a GM NP203 and GM NP205.
-High Angle Driveline rear CV flange and modified front flange.
-ORD Twin stick transfer case shifters.
-Custom built transfer case crossmember and skid plate, (needs the rear finished to cover the NP205).
$SOLD

Complete 1987 TBI 350 with harness, computer, and 31 gallon fuel tank with skid; this is a Jasper rebuild with around 30k on it, runs perfect $SOLD.

TH400 Art Carr shifter, plastic sleeve on the cable has a small burn from the exhaust, does not affect anything $SOLD

Package deal:
-Modified Hydroboost PS pump for hydro assist with extended neck (Originally bought from "The General")
-Modified steering box for hydro assist (Originally bought from "The General")
-Hydrobooster & MC
-WTO 8" 1.75" ram, one trail ride
-all hydraulic lines and fittings included
$SOLD

ORD bolt in brace $SOLD


I will post some pictures over the next few days.

 

[jackedjimmy350]

id take the ord bolt on brace

 

[84CUCV]

Sent you a pm pete

 

[yunit]

TIRES:

I started to groove one of the tires, but never finished it, the other tires are not grooved.

 

[jackedjimmy350]

guess i got beat out on the brace

 

[puckhead]

would you ship the 15x10 8 lugs to colorado and how much for the shipping?

 

[yunit]

would you ship the 15x10 8 lugs to colorado and how much for the shipping?

I might have a local buyer, I'll let you know if he backs out.

 

[blublaz]

xover steering

would like a chance to buy this if you still have it ....thanks Don

 

[yunit]

would like a chance to buy this if you still have it ....thanks Don

The axles and crossover steering are going on my new project truck.

 

[thatK30guy]

You were one of the first to have D60 front u-bolt plates made by TONYP, correct? If so, how much degree was milled into them? Want to part them, too? Price?

 

[yunit]

I only had one TonyP 8 degree u-bolt plate made for the carrier side, the normal spring pad on the driver side does not need it. I am going to hold onto the u-bolt plate until I put the axles in my new truck, I shouldn't need the u-bolt plate and shims, but cha never know. If I do not need them I will shoot you a PM. Pete.

Oh yeah, good to see you active on the site again Wes.

 

[thatK30guy]

I only had one TonyP 8 degree u-bolt plate made for the carrier side, the normal spring pad on the driver side does not need it. I am going to hold onto the u-bolt plate until I put the axles in my new truck, I shouldn't need the u-bolt plate and shims, but cha never know. If I do not need them I will shoot you a PM. Pete.

Oh yeah, good to see you active on the site again Wes.

Good to be back, Pete! I've been trying to get ahold of Tony with no luck. I've got Jeff (Muddytazz) working with me now for some plates and zero-rates.