It's been a long time since I've been active here, but it's come time to get the Blazer back on the road. I bought this truck in 2000, joined CK5 back then, and did a mild build on it to be able to go rock crawling. Sometime around 2012 or so, life got busy (married, career, raising 2 kids) and the truck sat. With our youngest child now a senior in high school, and soon to be empty nesters (hopefully!), the wife and I decided it's time to get the Blazer back on the road with a nice restomod.
Current config is:


Here are a few recent pics of how it sits today
:



My goal is to do a tasteful restomod on it, with a leaning toward comfortable street manners while retaining decent trail capabilities. The motor doesn't have many miles on it, so I plan to retain it and swap over to an EFI setup.
A buddy of mine has a 2022 Chevy 2500 pickup, and he replaced his wheels with some aftermarket rims. So I grabbed his OEM wheels and tried them out with some 2" adapters for the wheel stud spacing difference. I really like they way these rims look, and plan to keep them for the final outcome.
20" x 8.5" rims with the OEM 275/65 x 20 tires

I had AI do a mock-up picture, showing what the truck would look like with a new paint job, these wheels, and 35" tires ... Looks like a winner to me!

My plan right now is to get the motor running how I want, and then take the truck to a shop for the majority of the restomod work. Mainly because I just don't have the time to dedicate to what needs to be done.
Plan to get the motor running is ... swap the fuel tank for a 1987 or newer K5 TBI baffled tank, use an OEM hanger along with a 255LPH pump, new fuel lines, filter and regulator for 58 - 60 PSI, and install a Terminator X 4150 4-injector setup.
The same buddy who gave me the wheels has a new Holley Terminator Stealth throttle body he is giving me, so I'm on the hunt for the ECU, screen, O2 sensor and wiring harness.
Then I came across the Edlebrock EFI setup, as well as ACES, and a few others .. and wondered if I should be considered something other than the Terminator X setup.
Still some more research to do, but happy to be finally giving the Blazer some much overdue attention and thought I'd re-engage the CK5 community!
Current config is:
- 1984 K5 Blazer, 4x4, Silverado, originally with a 305 motor
- Motor was pulled in 2005, and I had a new one built at that time
- 350 bored to 355 SBC 4 bolt roller block
- 6" rods with matching pistons
- We reused the 305 heads
- Opened the chambers up to 63cc
- 3 angle valve job with mild porting, gasket matched
- 1.94 intake valves and 1.50 exhaust valves
- Comp 08-500-8 cam (XR258HR)
- 206*/212* duration (258*/264* advertised duration)
- 0.480/0.488 valve lift with 1.5 rockers
- 112* lobe separation
- Roller lifters, hardened pushrods, 1.5:1 roller rockers, guide plates
- Edelbrock performer dual plane intake
- SMI Stage 2 Quadrajet carb
- Hooker supercomp shorty headers
- Rebuilt and strengthened 700R4 trans
- Original NP208 transfer case
- GM 14 Bolt FF rear differential with Cadillac disc brake conversion
- Dana 44 front differential
- 4.10 gearing in the differentials
- 15" x 10" Steel wheels with 33" x 12.5" shot tires
- 2.5" lift
- Rear has 2.5" ORD shackle flip kit with some 1990 OEM leaf springs
- Front has 2" Tuff Country easy ride springs along with ORD heavy duty extended front shackles
- ORD steering box brace
- ORD Swaybar disconnect kit
- Manual locking hubs
Here are a few recent pics of how it sits today
:My goal is to do a tasteful restomod on it, with a leaning toward comfortable street manners while retaining decent trail capabilities. The motor doesn't have many miles on it, so I plan to retain it and swap over to an EFI setup.
A buddy of mine has a 2022 Chevy 2500 pickup, and he replaced his wheels with some aftermarket rims. So I grabbed his OEM wheels and tried them out with some 2" adapters for the wheel stud spacing difference. I really like they way these rims look, and plan to keep them for the final outcome.
20" x 8.5" rims with the OEM 275/65 x 20 tires
I had AI do a mock-up picture, showing what the truck would look like with a new paint job, these wheels, and 35" tires ... Looks like a winner to me!
My plan right now is to get the motor running how I want, and then take the truck to a shop for the majority of the restomod work. Mainly because I just don't have the time to dedicate to what needs to be done.
Plan to get the motor running is ... swap the fuel tank for a 1987 or newer K5 TBI baffled tank, use an OEM hanger along with a 255LPH pump, new fuel lines, filter and regulator for 58 - 60 PSI, and install a Terminator X 4150 4-injector setup.
The same buddy who gave me the wheels has a new Holley Terminator Stealth throttle body he is giving me, so I'm on the hunt for the ECU, screen, O2 sensor and wiring harness.
Then I came across the Edlebrock EFI setup, as well as ACES, and a few others .. and wondered if I should be considered something other than the Terminator X setup.
Still some more research to do, but happy to be finally giving the Blazer some much overdue attention and thought I'd re-engage the CK5 community!
