That's "disparate". As in "disparate is dead, no more, has shuffled off this mortal coil", etc.
Seriously, though, I don't know how you guys access the web from your phones and smaller tablets. I guess I just have fat fingers.
-- A
CK5
Register an account today to become a member! Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members.
1982 C/K 6.0L Caitlyn Mall Crawler (Interior time)
- Thread starter Babaganoosh
- Start date
That's "disparate". As in "disparate is dead, no more, has shuffled off this mortal coil", etc.
Seriously, though, I don't know how you guys access the web from your phones and smaller tablets. I guess I just have fat fingers.
-- A
andyblack
Registered Loser
Well I was close. 
Much better angle and I had the tie rod off a little bit with the wood so I clamped the metal to the rotors. Someone bumped into the truck while it has been sitting hte passed few weeks so it took some time to put it back into shape.
The drag link and pan hard bar have a .4 of a difference in angle the panhard is the difference, will this be ok?
ion
1/2 ton status
So uhhhhh........ is this truck going to be done this decade or no?
andyblack
Registered Loser
That looks way better to me. I don't think that less than one degree difference will matter at all. In fact I would think that would be considered a really good angle. Awesome job man! It's coming right along now.
Much better angle and I had the tie rod off a little bit with the wood so I clamped the metal to the rotors. Someone bumped into the truck while it has been sitting hte passed few weeks so it took some time to put it back into shape.
The drag link and pan hard bar have a .4 of a difference in angle the panhard is the difference, will this be ok?
much much better.. looks good man..
I hope so, once this suspension stuff is done I think it will come together even quicker.
I don't think so either, I'm really shocked how well I got it. It involved a 2x4 a jack stand holding it while I tacked it.
Thank you, I agree mucho better.
ion
1/2 ton status
Ya know I was really hoping for more of a piss and vinegar response out of you. You're losing your sassy-ness ben.
You are not the first or last one to say that it won't be done anytime soon.
y5mgisi
1 ton status
I have enjoyed the fact that you don't get your feathers ruffled easily.
I think you are all set now!
I think you are all set now!
As I type this reply my song came on.
Seems a fitting reply to you Mitch, life is to short to give up and cave in.
Seems a fitting reply to you Mitch, life is to short to give up and cave in.
Last edited by a moderator:
Sense the new steering arm went on now my pan hard is a inch shorter then the drag link. Should I space the inserts out a little and turn the heims to make up for the inch?
That won't work, either I leave it, add a little material on the panhard bracket, or order up another bracket.
Should I space the inserts out a little and turn the heims to make up for the inch?That won't work, either I leave it, add a little material on the panhard bracket, or order up another bracket.
y5mgisi
1 ton status
Personally, I think you will be Aight.
What's the song? My phone says I'm not allowed to see it.
What's the song? My phone says I'm not allowed to see it.
Run it. You can not make it perfect. There is not a truck out there with arms, coilovers and panhard bar that is perfect. There is always give and take.
It's I hold on by Dierks Bentley
Does this look right for a 4 inch and 33's?
Tires measure 31.5 tall
Does this look right for a 4 inch and 33's?
Tires measure 31.5 tall
y5mgisi
1 ton status
Looks almost perfect. I think if anything it might actually be slightly low still? I would measure from somewhere and ask someone with either a stock truck, or a 4" lift truck to measure theirs.
I'm checking out this thread for visual inspections, but I'm not sure I'm going to talk to Adam and get me some measurements.
http://coloradok5.com/forums/showthread.php?t=170627
http://coloradok5.com/forums/showthread.php?t=170627
y5mgisi
1 ton status
Yep. I think if I was you I would set it right where you have it.
Don't really want to cut but I want the option to fit 35's some day. I think I should just run it at this height if It is close to a 4 inch and 33's "look"
