CK5
Register an account today to become a member! Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members.
72 Jimmy PO has me PO'd
- Thread starter jaros44sr
- Start date
Got a little more done on my handbrakes
1638120110056388572440635201578 by https://www.flickr.com/photos/97391199@N06
1638120110056388572440635201578 by https://www.flickr.com/photos/97391199@N06
16401849429525845957225115628482 by https://www.flickr.com/photos/97391199@N06Finished up my dual emergency brake handles
16458932914272783050843789695736 by https://www.flickr.com/photos/97391199@N06Found some time to hang my BBWM......
Mounting system, 3/8-16 hex drive studs, with square nuts and serrated flange nuts
16459604620537441224320595081536 by https://www.flickr.com/photos/97391199@N06
Thanks Ben for offering an excellent product, that powder coating is very tough, dropped some pieces with no damage
Now I have to order the shackle kit, should've listened to you lol
16459604620537441224320595081536 by https://www.flickr.com/photos/97391199@N06Thanks Ben for offering an excellent product, that powder coating is very tough, dropped some pieces with no damage
Now I have to order the shackle kit, should've listened to you lol
Last edited:
looking good!Mounting system, 3/8-16 hex drive studs, with square nuts and serrated flange nuts
Thanks Ben for offering an excellent product, that powder coating is very tough, dropped some pieces with no damage
Now I have to order the shackle kit, should've listened to you lol
Thanks for the support!
THE BEST aftermarket part I have ever installed, great directions, communication and, tuff powder coating
Just waiting on shackle mounts, to finish job
Also, have to clock motor for feet up install, something about drain holes
Thanks again for all your work
16464912967791948126542440289921 by https://www.flickr.com/photos/97391199@N06Talked to Warn service, they said to clock the motor and grind a bleed hole in the bottom of the mount, for a feet up application
We'll see how that goes, separated motor at cross rods to eliminate the problem of pulling armature brushes out of motor
This is about what she looks like in her present form
20190829_100523 by https://www.flickr.com/photos/97391199@N06
20190829_100523 by https://www.flickr.com/photos/97391199@N06
Looks like a sbc TPI intake?
Martin
Martin
Yes, read all your posts on the subject, great advice, still has to go back to the tuner for a final tune
Ha, I was thinking of a different thread. I am excited to see this running and driving.
Martgin
Martgin
This what I want to accomplish, just have to find an end mill, about .300, and a suitable mounting to clamp in place
16465783711852758522316813132959 by https://www.flickr.com/photos/97391199@N06
16465783711852758522316813132959 by https://www.flickr.com/photos/97391199@N06
Can't wait to install, s/b here Tuesday according to UPS.Wow Thank you
Shackles shipped yesterday
What ton press does it take to bend that steel? Or is it proprietary
Jim
This is my set up, I want to mill bleed hole at the BLUE MARKER or directly on center which is motor mounting hole and clocking hole, not sure which I'll do, yet
16466585817548968768472028304497 by https://www.flickr.com/photos/97391199@N06
You can see the OEM slot at 6 o'clock
16466585817548968768472028304497 by https://www.flickr.com/photos/97391199@N06You can see the OEM slot at 6 o'clock
Last edited:
Changed my set up, moved vice jaws and used a V block
16466663267856965690023610472617 by https://www.flickr.com/photos/97391199@N06
16466663267856965690023610472617 by https://www.flickr.com/photos/97391199@N06
