MrDJ
DJ404564X4
Very comfortable. They recline have sliders, lumbar support, and seat heaters. I need to figure out how to get a couple more inches of leg room but other than that I really like them.
CK5
Register an account today to become a member! Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members.
DJz Blazer
- Thread starter MrDJ
- Start date
Very comfortable. They recline have sliders, lumbar support, and seat heaters. I need to figure out how to get a couple more inches of leg room but other than that I really like them.
Nice, I like the seats too. I didn't know they came with all that. I wouldn't mind some of those myself. cost?
MrDJ
DJ404564X4
I got a deal as I know the owner. I don't remember what retail was. I think under 1500 with sliders? Plus harness's. I also got extra wide and extra tall. Daily drivers.
MrDJ
DJ404564X4
So I might be without a trailer this year at KOH so I'm thinking of flat towing the Blazer out there.
Just put everything in neutral?
Anyone make some nice bolt on tow points for the blazer?
Just put everything in neutral?
Anyone make some nice bolt on tow points for the blazer?
MrDJ
DJ404564X4
Just make sure your heater is in the 'High" position.
But what fan speed and should I leave the dome light on??
MrDJ
DJ404564X4
Now my headlights no worky but the marker and tail lights work??
WTF??
WTF??
Check your brights switch. I've had it get stuck half way on and cause the headlights to not work.
MrDJ
DJ404564X4
I jumped up and down on the dimmer switch. I knew I replaced it so didn't look at it that hard.
It was unplugged.
Last edited:
MrDJ
DJ404564X4
Forgot I had these mounts for my TJ. I should be able to get a plate welded to both frame rails to mount them to.
MrDJ
DJ404564X4
And then...
MrDJ
DJ404564X4
Front diff cover was rusted up pretty good.
MrDJ
DJ404564X4
Fluid coming out weren't to purdy too.
MrDJ
DJ404564X4
Call Matt for a new Solid cover.
MrDJ
DJ404564X4
New interior showed up..
MrDJ
DJ404564X4
Ram horns!
Peter Griffth voice to roadhouse...
Peter Griffth voice to roadhouse...
ekajkrats
1/2 ton status
Ooooh, I've been thinking about a pair of those. What do they measure at the collector? No need to spend any time looking if you don't know off the top of your head (google can always tell me too). Where did you end up getting them from?
MrDJ
DJ404564X4
Not sure but they fit nice and tight. I already have them on the Blazer. These are replacement manifolds because I'm going to install the exhaust off the donor Blazer as it has Flow Master Super 40s on it and I have a old rated out exhaust with entirely to quiet exhaust.
ekajkrats
1/2 ton status
Nice. I would definitely run the rams too if upgrading the exhaust.
My exhaust isnt totally ratted out yet though, just slightly rattly going down the road. The super 40s would be just a tad too loud for my preference, but at the price of free (or free with purchase of parts truck) I would give them a shot too.
My exhaust isnt totally ratted out yet though, just slightly rattly going down the road. The super 40s would be just a tad too loud for my preference, but at the price of free (or free with purchase of parts truck) I would give them a shot too.
bp71k5
3/4 ton status
Just an FYI if interested, the old corvettes (forgot the year) also use rams horn manifolds that are larger at the outlet for better flow. It was a noticeable difference in power when I swapped them on. You can get two left side ones from any autoparts store and grind off the accessory bosses you don't need.
