CK5
Register an account today to become a member! Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members.
77K5. The IronMaiden...9/2 headed for Blazer Bash 20!
- Thread starter 76zimmer
- Start date
-
- Tags
- 14bff bearing desintigrated 454 cookies custom diy4x aluminum fuel tank diy4x flatback dif covers diy4x frame boxing kit diy4x wraptor/truss ez-efi fords suck hemi orange and school bus yellow index l&l headers long/dana coolers making me her bitch. more tranny problems one tons phoenix trans convertor th400 full manual
jack of all trades build, overland, dunes, rocks, trails
someone is having too much fun with a laser cutter 
Kert makes key holders now!
Cool!
Cool!
Kert makes key holders now!
Cool!
actually its a coat rack!
I was hoping it was your new grille with a location to wrap up recovery things like straps...
Nice stuff Kert
I was hoping it was your new grille with a location to wrap up recovery things like straps...
That would be cool Colby, got another style in mind for the grille...more tube and expanded metal!
Ah didn't know it was that big.
Those little holes are 16" on center for mounting to studs!
That would be cool Colby, got another style in mind for the grille...more tube and expanded metal!
Those little holes are 16" on center for mounting to studs!
and 3/16" diameter for screws. Just throwin' that out for some scale. Its a pretty big piece actually.
You suppose thats a 14 bolt?
Good thinking guys... I like it.
and 3/16" diameter for screws. Just throwin' that out for some scale. Its a pretty big piece actually.
You suppose thats a 14 bolt?
a SF14 maybe, it don't stick down far enough for a FF..
been working in the shop lately, but not on the Maiden....time for a compressor upgrade....wondering if/when the ole single stage oiless POS compressor would blow another rod...probably at the worst time...so out with the old:
And in with the new:
60 gal. 5hp. two stage 175psi.= 15.5 cfm
So I started rerouting plumbing, then that ballooned into rewiring, then cleaning out the shop to make more room, get rid of some JUNK and reorganize the rest of the stuff that stays. Should be here next week sometime...once I get the shop put back together I need to get on the Maiden heavy...headed to Kerts place in March to pick up a bunch of stuff.
And in with the new:
60 gal. 5hp. two stage 175psi.= 15.5 cfm
So I started rerouting plumbing, then that ballooned into rewiring, then cleaning out the shop to make more room, get rid of some JUNK and reorganize the rest of the stuff that stays. Should be here next week sometime...once I get the shop put back together I need to get on the Maiden heavy...headed to Kerts place in March to pick up a bunch of stuff.
whatya doin with the old one?
got the new compressor in this week, set in place, wired, and started piping.
So much quieter now!
Running a filter then a regulator, then out to 4 drops....
Put in an outside port w/ some outlets too....something I wish I had done since I built the shop.
So much quieter now!
Running a filter then a regulator, then out to 4 drops....
Put in an outside port w/ some outlets too....something I wish I had done since I built the shop.
Stainless fittings dave??? DAAAYYYYUUUUUUMMMM
Looks really nice!
Now you should be able to get a lot more work done now.
Now you should be able to get a lot more work done now.
Stainless fittings dave??? DAAAYYYYUUUUUUMMMM
Adam, this is one reason why pharmaceuticals cost so dam much, everything in product contact is stainless...and they throw a ****load of it to scrap....well they clean up pretty good I must say! Some have some boogered threads, others maybe a bunch of sealant or attached to a bad valve or flange, but a little time spent on them makes em usable for me!
Looks really nice!
Now you should be able to get a lot more work done now.
A shop without air seems so unfulfilled
