4000. 6000. Just 2000rpm is what separates the boys from the men.
CK5
Register an account today to become a member! Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members.
LSX454 swapped 95 BASS burb.
- Thread starter shady
- Start date
Little lower, little cooler, bigger sounds.
I spin my "stock" LQ4 to 7,000
My shift points will be 6300-6500 eventually.
But I've seen that when it starts to shift to where it actually shifts takes enough time that it'll rev 300-400 over the actual shift points. So shifting there keeps me just under what I consider redline.
GM used to promote this as a 7100 rpm redline. Now it says 6500 on most sites. So I'm going to leave it at the 6900 I had before for good measure.
And because, you know, 69... Lol
But I've seen that when it starts to shift to where it actually shifts takes enough time that it'll rev 300-400 over the actual shift points. So shifting there keeps me just under what I consider redline.
GM used to promote this as a 7100 rpm redline. Now it says 6500 on most sites. So I'm going to leave it at the 6900 I had before for good measure.
And because, you know, 69... Lol
Babaganuked... lol That's how that happens.
Chit happens when you party naked
It's angel dust holms
Theres a pic on the wall of my shop of me, drunk, passed out, nekkid AF, at 18 yrs old.
Luckily it's taken in a way that doesn't show anything bad. Lol.
It's the only time in my life that I partied hard enough to not remember the whole party.
I partied plenty hard after that, but always knew the limit then.
The others at the party (my cousins) tried to sober me up by putting me in the shower but I wouldn't cooperate... So they figured it was because my clothes were on.
So they had the girls strip me.. Then none of the dudes wanted to put me in the shower anymore.
So they left me on the floor and were hosing me there with the shower wand when the grownups that had been called showed up to take over the situation.
They took the pics lol.
Luckily it's taken in a way that doesn't show anything bad. Lol.
It's the only time in my life that I partied hard enough to not remember the whole party.
I partied plenty hard after that, but always knew the limit then.
The others at the party (my cousins) tried to sober me up by putting me in the shower but I wouldn't cooperate... So they figured it was because my clothes were on.
So they had the girls strip me.. Then none of the dudes wanted to put me in the shower anymore.
So they left me on the floor and were hosing me there with the shower wand when the grownups that had been called showed up to take over the situation.
They took the pics lol.
I opened up the shift points, raised the rev limiter and started playing.....
There isn't a big enough smiley to cover how happy I am now .
Unfuggin believable!
I've found that it's hard to even flog it... I sub consciously only give it 1/2-3/4 pedal because it doesn't even need more lol.
I'm going to have to leave it in second to even hit 6k with it. In 3rd I'm doing 90+ at 5k-5500 lol.
Even if it still doesn't do standing crazy burnouts.... I don't care lol. It's a friggin BLAST to drive.
There isn't a big enough smiley to cover how happy I am now .
Unfuggin believable!
I've found that it's hard to even flog it... I sub consciously only give it 1/2-3/4 pedal because it doesn't even need more lol.
I'm going to have to leave it in second to even hit 6k with it. In 3rd I'm doing 90+ at 5k-5500 lol.
Even if it still doesn't do standing crazy burnouts.... I don't care lol. It's a friggin BLAST to drive.
Now, put a blower on it.
My tundra is 10.2:1 and I’m running 7psi and folks run 14psi from a supercharger on pump gas. You can do it.
This is going to move on to beautification.
If I SC anything it'll be an LSA on the old engine that's now going in my Cutlass.
I have to get that in and running so we can drive it and turn heads. Once I do that, my wife might let me crank it up a little lol.
As it is now she already wants to beef up her Yukon and put an exhaust on it. Cause she's jealous of this burb
If I SC anything it'll be an LSA on the old engine that's now going in my Cutlass.
I have to get that in and running so we can drive it and turn heads. Once I do that, my wife might let me crank it up a little lol.
As it is now she already wants to beef up her Yukon and put an exhaust on it. Cause she's jealous of this burb
When you combine cubic inches with modern LS7 heads and valvetrain you get some fun ponies!
Those are LSX heads, with different castings and more head bolts. What did you read is failing on LS7 heads?
