What's new
CK5
Register an account today to become a member! Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members.

Media

floor looking finished

floor looking finished

  • 0
  • 0
Work and rain slowed me up for a few days

Work and rain slowed me up for a few days

  • 0
  • 0
I really like the seats. I paid $450 for both with slider rails

I really like the seats. I paid $450 for both with slider rails

  • 0
  • 0
new seats needed some bracket fab work to match the old seat brackets

new seats needed some bracket fab work to match the old seat brackets

  • 0
  • 0
didn't grind the weld, just some color close Rustoleum for a couple months

didn't grind the weld, just some color close Rustoleum for a couple months

  • 0
  • 0
I just did not want the rust to keep growing while I waited to do body work

I just did not want the rust to keep growing while I waited to do body work

  • 0
  • 0
Piece of a patch panel

Piece of a patch panel

  • 0
  • 0
of course, the inner wheel house was rusted too

of course, the inner wheel house was rusted too

  • 0
  • 0
rust was showing thru on the right quarter, I wanted to wait to redo the body, so just a quick rust cut and patch

rust was showing thru on the right quarter, I wanted to wait to redo the body, so just a quick rust cut and patch

  • 0
  • 0
It gave me way more room underneath, so I was finally able to make a nice turbo down pipe, and not have it hitting the floor

It gave me way more room underneath, so I was finally able to make a nice turbo down pipe, and not have it hitting the floor

  • 0
  • 0
I figured I would take the opportunity to make room for my turbo down pipe.

I figured I would take the opportunity to make room for my turbo down pipe.

  • 0
  • 0
if it took 32 years to rust out, I figure replacing the rusted pieces with stainless would last a long time

if it took 32 years to rust out, I figure replacing the rusted pieces with stainless would last a long time

  • 0
  • 0
reused the lower seat belt nut plate

reused the lower seat belt nut plate

  • 0
  • 0
I used mild mig wire, and it welded the mild steel to the stainless fine

I used mild mig wire, and it welded the mild steel to the stainless fine

  • 0
  • 0
everything up front I fixed with 1/8" stainless

everything up front I fixed with 1/8" stainless

  • 0
  • 0
rear seat foot wells cut out

rear seat foot wells cut out

  • 0
  • 0
rear floor welded up

rear floor welded up

  • 0
  • 0
at the same time I would rework the roll cage.

at the same time I would rework the roll cage.

  • 0
  • 0
up front didn't look as bad, but some holes and weak spots needed attention

up front didn't look as bad, but some holes and weak spots needed attention

  • 0
  • 0
before cutting out the back

before cutting out the back

  • 0
  • 0
I cut the metal I needed from a clean long box floor for the rear floor repairs

I cut the metal I needed from a clean long box floor for the rear floor repairs

  • 0
  • 0
the whole back section of the box needed to be replaced

the whole back section of the box needed to be replaced

  • 0
  • 0
By the fuel filler relief

By the fuel filler relief

  • 0
  • 0
Found a ton of rust in my floor...carpet was wet. After pulling the carpet in the rest of the truck, it was clear I had work to do

Found a ton of rust in my floor...carpet was wet. After pulling the carpet in the rest of the truck, it was clear I had work to do

  • 0
  • 0
Top Bottom